Perc 6i Unraid, I am leaning towards I have a Dell Perc 6/e card (L

Perc 6i Unraid, I am leaning towards I have a Dell Perc 6/e card (LSI SAS 1078) that I would like to use to expand out my unRAID server. 2TB. OS Support: Microsoft Windows, Linux (SuSE, Red Hat), Solaris, VMware, FreeBSD See the downloads Server: R410 RAID Card: PERC6i Drives: WD Red Pro 3TB Hi all, Unraid isn't recognising any drives whatsoever, the only drives are "unassigned", from reading, unraids kernel does not support this type of raid card and or virtual disks, it wants full access to the disks. This is just adding a load more complexity and completely bypasses the purpose of Unraid. 200-250 maybe. I am unable to have any drives or parity show up. I have tried 2 10k sas drives and 1 samsung 120 pro sata drive. This controller doesn't support drives bigger than 2. For me, I plan to build an UNRAID system with a T310 base/Xeon X3440, and will likely do a blog on it. The other PCIe slot is being used for additional network ports to support running pfSe Hi All, I'm a newbie to home server design, and I'm trying to put together a home server to serve my NAS needs (most likely Unraid). Jun 16, 2023 · My solution was to change my Perc 6i to an H700 to accomodate larger drives. This particular server came with a SAS 6/iR Integrated from the factory. I've done a bit of searching on the forum and while I found one post about a H200 I've not found anything that tells me if it is compatible with unRAID or not. 5 inch) to large one such as 3TB /4TB. aspx?c=ca&a To get past the 2TB limit on the i6 as well as something that works with unraid, what kind of card should I be looking at? I don't need anything that can do a raid of course, Just something that can support 8 drives. Avago's website is a mess. Don't create a RAID drive. 6 running on a Dell R310 w/ H200 controller running in IT mode connected to four 4TB SATA drives and 16GB of RAM. Could you provide me with the official part number for the PERC 6/i by chance so I can do some more looking? Hi guys, PCI-e (8x) Dell SAS card for sale. The only problem with the PERC 5 card is that it doesn't have the capability to configure RAID 6, which what I would prefer to be using. txt before starting! Is this a hardware limitation ? My PERC 6/i has the following software installed : FirmWare 1. Was spec'd for a server in error and the card is sat here not doing much. 0Beta7 added 3TB Drive support) Drive Spin Down support: YES (UPDATE: Added as of 5. Hi All, I currently have Unraid 6. 1. Hey Everyone, I just picked up a good deal on a Dell PowerEdge T310. Whats causing this issue? Hi All, I've just got a Dell r710 server that I want to run unRAID on. I currently have the stock Perc 6i card in there. 0Beta7) Make sure you read and understand the __READMEFIRST. 3. I made the swap physically, on boot my bios or raid setup utility One thing to remember the PERC/6 family is based around the LSI 1068/78 series RAID, that means it's SAS2 6gbps but SATA II 3gbps, and is limited to 2TB disks. What would you recommend for a replacement? Reading these forums the H200 (IT Mode) and HBA330 seem to be good candidates. I have a question for anyone that may have experience with Dell Servers. I have tried configuring them in raid 0, 1, unconfigured, and as single virtual drives. 29 Battery Management. dell. I'm guessing you mean perc 6i, no it is not a good card to use in unraid. Virtual disks that were created on the PERC 5 family of controllers can be migrated to the PERC 6 and CERC 6i controllers without risking data or configuration loss. 29 Migrating Virtual Disks from SAS 6/iR to PERC 6 and CERC 6i . This is the card: http://accessories. I've bought a Dell PowerEdge R710 with 3. This gives me 6gb/s to the drives, but takes up a PCIe slot. 52-1909, BIOS 2. I am not that knowledgeable in server hardware and I was wondering if anyone could recommend a suitable (lower cost) replacement and any adaptors required that would work with UNRAID. com/sna/productdetail. It looks like those longer-width connectors need to be replaced with sas connectors for this card. Any help would be very much appreciated, I have 2 r610 w/ perc 6i and really need to get to an IT firmware. I just got a server with a PERC 6i in it which then connects to the 6 drive bays on the front. If you are using an old server that uses PERC/CERC BIOS Configuration Utility, please refer to the article we wrote earlier about how to create RAID on DELL Servers using PERC/CERC BIOS Configuration Utility (with screenshots). 28 Compatibility With Virtual Disks Created on SAS 6/iR Controllers . 6. Unfortunately while my hardware supports vt-d, there is a glitch in the cpu/chipset that prevents this LSI SAS Disk Controllers & RAID Cards 6 RAID Levels Raid Card LSI 9340-8i SAS Controller Flashed To IT Mode - 9300-8i P16 Firmware For ZFS FreeNAS UnRAID Systems Lsi Raid Controller LSI SAS Disk Controllers & RAID Cards 2 RAID Levels Chip: SAS3008. 9gkacg, b6g6, n9zq6, hghz, 87f35, gcgxn, 1xspr, zxxa, j0m3, wn9lc,